DEVELOPMENT OF THE METAL RHEOLOGY MODEL OF HIGH-TEMPERATURE DEFORMATION FOR MODELING BY FINITE ELEMENT METHOD

Oleg Markov, Oleksiy Gerasimenko, Leila Aliieva, Alexander Shapoval

Abstract


It is shown that when modeling the processes of forging and stamping, it is necessary to take into account not only the hardening of the material, but also softening, which occurs during hot processing. Otherwise, the power parameters of the deformation processes are precisely determined, which leads to the choice of more powerful equipment. Softening accounting (processes of stress relaxation) will allow to accurately determine the stress and strain state (SSS) of the workpiece, as well as the power parameters of the processes of deformation. This will expand the technological capabilities of these processes. Existing commercial software systems for modeling hot plastic deformations based on the finite element method (FEM) do not allow this. This is due to the absence in these software products of the communication model of the component deformation rates and stresses, which would take into account stress relaxation. As a result, on the basis of the Maxwell visco-elastic model, a relationship is established between deformation rates and stresses. The developed model allows to take into account the metal softening during a pause after hot deformation. The resulting mathematical model is tested by experiment on different steels at different temperatures of deformation. The process of steels softening is determined using plastometers. It is established experimentally that the model developed by 89 ... 93 % describes the rheology of the metal during hot deformation. The relationship between the components of the deformation rates and stresses is established, which allows to obtain a direct numerical solution of plastic deformation problems without FED iterative procedures, taking into account the real properties of the metal during deformation. As a result, the number of iterations and calculations has significantly decreased.


Keywords


hot deformation; hardening; softening; stress relaxation; FEM; hardening curve; pause; energy-power parameters; forging and stamping

Full Text:

PDF

References


Markov, O., Zlygoriev, V., Gerasimenko, O., Hrudkina, N., Shevtsov, S. (2018). Improving the quality of forgings based on upsetting the workpieces with concave facets. Eastern-European Journal of Enterprise Technologies, 5 (1 (95)), 16–24. doi: https://doi.org/10.15587/1729-4061.2018.142674

Buckingham, R. C., Argyrakis, C., Hardy, M. C., Birosca, S. (2016). The effect of strain distribution on microstructural developments during forging in a newly developed nickel base superalloy. Materials Science and Engineering: A, 654, 317–328. doi: https://doi.org/10.1016/j.msea.2015.12.042

Ma, F., Lu, W., Qin, J., Zhang, D., Ji, B. (2007). The effect of forging temperature on microstructure and mechanical properties of in situ TiC/Ti composites. Materials & Design, 28 (4), 1339–1342. doi: https://doi.org/10.1016/j.matdes.2006.02.004

Ma, Q., Lin, Z., Yu, Z. (2009). Prediction of deformation behavior and microstructure evolution in heavy forging by FEM. The International Journal of Advanced Manufacturing Technology, 40 (3-4), 253–260. doi: https://doi.org/10.1007/s00170-007-1337-9

Pantalé, O., Gueye, B. (2013). Influence of the Constitutive Flow Law in FEM Simulation of the Radial Forging Process. Journal of Engineering, 2013, 1–8. doi: https://doi.org/10.1155/2013/231847

Wu, Y., Dong, X., Yu, Q. (2015). Upper bound analysis of axial metal flow inhomogeneity in radial forging process. International Journal of Mechanical Sciences, 93, 102–110. doi: https://doi.org/10.1016/j.ijmecsci.2015.01.012

Kukhar, V., Burko, V., Prysiazhnyi, A., Balalayeva, E., Nyhnibeda, M. (2016). Development of alternative technology of dual forming of profiled workpiece obtained by buckling. Eastern-European Journal of Enterprise Technologies, 3 (7 (81)), 53–61. doi: https://doi.org/10.15587/1729-4061.2016.72063

Dobrzański, L. A., Grajcar, A., Borek, W. (2008). Influence of hot-working conditions on a structure of high-manganese austenitic steels. Journal of Achievements in Materials and Manufacturing Engineering, 29 (2), 139–142.

Weides, G., Blaes, N., Bokelmann, D. (2008). Optimisation of the forging process of profiled discs for low pressure turbine rotors by FEM simulation. 17 International Forgeмasters Meeting, Santander.

Erman, E., Medei, N. M., Roesch, A. R., Shah, D. C. (1989). Physical modeling of the upsetting process in open-die press forging. Journal of Mechanical Working Technology, 19 (2), 195–210. doi: https://doi.org/10.1016/0378-3804(89)90004-1

Markov, O. E., Perig, A. V., Markova, M. A., Zlygoriev, V. N. (2015). Development of a new process for forging plates using intensive plastic deformation. The International Journal of Advanced Manufacturing Technology, 83 (9-12), 2159–2174. doi: https://doi.org/10.1007/s00170-015-8217-5

Kitamura, K., Terano, M. (2014). Determination of local properties of plastic anisotropy in thick plate by small-cube compression test for precise simulation of plate forging. CIRP Annals, 63 (1), 293–296. doi: https://doi.org/10.1016/j.cirp.2014.03.038

Markov, O. E. (2012). Forging of large pieces by tapered faces. Steel in Translation, 42 (12), 808–810. doi: https://doi.org/10.3103/s0967091212120054

Mitani, Y., Mendoza, V., Osakada, K. (1991). Analysis of rotor shaft forging by rigid-plastic finite element method. Journal of Materials Processing Technology, 27 (1-3), 137–149. doi: https://doi.org/10.1016/0924-0136(91)90049-k

Markov, O. E., Perig, A. V., Zlygoriev, V. N., Markova, M. A., Grin, A. G. (2016). A new process for forging shafts with convex dies. Research into the stressed state. The International Journal of Advanced Manufacturing Technology, 90 (1-4), 801–818. doi: https://doi.org/10.1007/s00170-016-9378-6

Dragobetskii, V., Zagirnyak, M., Naumova, O., Shlyk, S., Shapoval, A. (2018). Method of Determination of Technological Durabilityof Plastically Deformed Sheet Parts of Vehicles. International Journal of Engineering & Technology, 7 (4.3), 92–99. doi: https://doi.org/10.14419/ijet.v7i4.3.19558




DOI: http://dx.doi.org/10.21303/2461-4262.2019.00877

Refbacks

  • There are currently no refbacks.




Copyright (c) 2019 Oleg Markov, Oleksiy Gerasimenko, Leila Aliieva, Alexander Shapoval

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

ISSN 2461-4262 (Online), ISSN 2461-4254 (Print)