MODIFIED HEXANIT CUTTERS FOR KNURLING OF CYLINDRICAL SHAFT SECTIONS

Bogdan Korobko, Ievgen Vasyliev, Stanislav Popov, Anatoly Vasilyev

Abstract


The possibility of using conventional cutters, in which the super-hard materials Hexanit R acts as the material for the diamond knurling of shaft sections made of steel 10, has been investigated. It is recommended to use damaged replaceable tips with super-hard material as tool blanks, which requires either re-grinding or recycling. The possibility of restoring the working properties of such cutters by regrinding is established, provided that the core of the tool is precisely located relative to the axis of rotation of the workpiece. The design of tooling in the form of a mandrel for fixing the tool on a lathe is proposed. It allows flexible clamping of the tool to the workpiece. Design and operational processing parameters are recommended for diamond knurling using tips made of superhard Hexanit-R material: knurler radius –5 mm; clamping forces – 200 N; feed – 0.05 mm/rev; workpiece rotation frequency – 630 rpm. According to the knurling results, the roughness was Ra 0.8 μm when lubricated with I-20A mineral industrial oil. An increase in the number of passes greater than four did not lead to a significant improvement in surface roughness. No signs of wear, damage to the working surface of the tool after an operating time of 40 hours were found.


Keywords


diamond smoothing; knurling; knurler; turning tool; Hexanit R; superhard materials

Full Text:

PDF

References


Vasilyev, A., Popov, S., Vasilyev, E., Pavelieva, A. (2017). Improving the method of rotational broaching in the production of profile openings on the lathes of turning group. Eastern-European Journal of Enterprise Technologies, 1 (1 (85)), 4–9. doi: http://doi.org/10.15587/1729-4061.2017.92256

Vasilyev, Ye. A., Popov, S. V., Vasilyev, A. V. (2016). Improving the efficiency of deep drilling with spiral drills in the processing of parts made of steel material 40. Bulletin of the National Technical University "Kharkiv Polytechnic Institute". Series: Mechanical-technological systems and complexes, 49 (1221), 75–79.

Aliev, I. S., Matviychuk, V. A. (2008). Investigation of the influence of surface plastic deformation on the state of the surface layer and service characteristics of products. Newsletter of Kyiv Polytechnic. In-t machine-blowing, 54, 13–20.

Stepanova, T. Yu. (2009). Technology of surface hardening of machine parts. Ivanovo: Ivan. state chemical technol. Univ., 64.

Kabatov, A. A. (2013). Analysis of finishing methods of surface plastic deformation processing. Open information and computer integrated technologies, 58, 49–54.

Dyl, T. (2011). The burnishing strengthen shafts neck of centrifugal pumps. Journal of KONES Powertrain and Transport, 8 (2), 123–128.

Borkar, A. P., Kamble, P. S., Seemikeri, C. Y. (2014). Surface Integrity Enhancement of Inconel 718 by using Roller Burnishing process. Journal of Current Engineering and Technology, 4 (4), 2595–2598.

Kundrak, J., Felho, C. (2016). 3D parameters of surface face milled by special tools. Manufacturing Technology, 16 (3), 532–538.

Gomez-Gras, G., Travieso-Rodriguez, J. A., Jerez-Mesa, R. (2015). Experimental Characterization of the Influence of Lateral Pass Width on Results of a Ball Burnishing Operation. Procedia Engineering, 132, 686–692. doi: http://doi.org/10.1016/j.proeng.2015.12.548

Loh, N. H., Tam, S. C. (1988). Effects of ball burnishing parameters on surface finish – A literature survey and discussion. Precision Engineering, 10 (4), 215–220. doi: http://doi.org/10.1016/0141-6359(88)90056-6

Posdzich, M., Stöckmann, R., Morczinek, F., Putz, M. (2018). Investigation of a plain ball burnishing process on differently machined Aluminium EN AW 2007 surfaces. MATEC Web of Conferences, 190, 11005. doi: http://doi.org/10.1051/matecconf/201819011005

Smoothers made of synthetic diamonds Rvert. = 1 mm (Ф10х12) 0.8 carats 624 UAH. Available at: https://prom.ua/p839916405-vyglazhivateli-sinteticheskih-almazov.html Last accessed: 27.12.2019

Vyglazhivatel almaznii ST-5 s okhlazhdeniem. Available at: https://tiu.ru/p214967902-vyglazhivatel-almaznyj-ohlazhdeniem.html Last accessed: 27.12.2019

Cutter hexanite-R (D8xH6.5xL16) angle 45/15 boring (601102) 300 UAH. Available at: https://prom.ua/p671602147-rezets-geksanit-rd8hh65hl16.html Last accessed: 27.12.2019




DOI: http://dx.doi.org/10.21303/sr.v0i1.1147

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 Bogdan Korobko, Ievgen Vasyliev, Stanislav Popov, Anatoly Vasilyev

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

ISSN 2313-8416 (Online), ISSN 2313-6286 (Print)