THE INFLUENCE OF THE GAPS IN THE MECHANICAL TRANSMISSION OF THE REDUCER OF THE SWITCH ELECTRIC DRIVE

Serhii Buriak

Abstract


Switch electric drives are one of the most important and responsible components of railway automation, and therefore require the development and implementation of advanced diagnostic systems. Achievement of the goal is possible only through the use of modern mathematical and software tools. There is a problem in the use of electric motors for switch electric drives today. The point is that the nature of the load on the engine is determined by the reducer. Deterioration appears on the reducer during operation. The appearance of gaps between the gears causes the instability of the load on the shaft. Measurements and control of the size of the gaps is not performed. To solve this problem, it is proposed to use linear measurement of the gaps of the gears and further modelling of the reducer. This method will allow to determine the arising load fluctuations by the deviation of the angular velocities of rotation of the drive and driven shafts. The effect of the gaps on the system operation is shown by model in the form of transfer functions of the constituent elements and the system of equations. It will be possible to set limit values for the deterioration of the gears of the reducer by the determination the maximum deviation of shafts angular speeds of rotation in order to take measures in advance for their timely replacement and to keep the engines from excessive load.


Keywords


еlectric motor; switch electric drive; railway automatics; mechanical transmission; reducer; single-mass system

Full Text:

PDF

References


Vileiniskis, M., Remenyte-Prescott, R., Rama, D. (2015). A fault detection method for railway point systems. Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 230 (3), 852–865. doi: https://doi.org/10.1177/0954409714567487

Kolpahchyan, P., Zarifyan, A., Jr. (2015). Study of the asynchronous traction drive's operating modes by computer simulation. Part 2: simulation results and analysis. Transport Problems, 10 (3), 5–15. doi: https://doi.org/10.21307/tp-2015-029

Ivanov, G. Ya., Kuznetsov, A. Yu., Dmitriev, V. V. (2011). Elektroprivod i elektrooborudovanie. Novosibirsk, 56.

Ivanov-Smolenskiy, A. V. (2004). Elektricheskie mashiny. Vol. 1. Moscow: Izdatel'stvo MEI, 656.

Dayneko, V. A., Kovalinskiy, A. I. (2008). Elektrooborudovanie sel'skohozyaystvennyh predpriyatiy. Minsk: Novoe znanie, 320.

Theeg, G., Vlasenko, S. (2009). Railway Signalling and Interlocking. International Compendium. Hamburg: Eurailpress.

Reznikov, Yu. M. (1985). Elektroprivody zheleznodorozhnoy avtomatiki i telemehaniki. Moscow: Transport, 288.

Chornyi, O. P., Luhovoi, A. V., Rodkin, D. Y., Sysiuk, H. Yu., Sadovoi, O. V. (2001). Modeliuvannia elektromekhanichnykh system. Kremenchuk, 410.

Oh, Y. J., Liu, H.-C., Cho, S., Won, J. H., Lee, H., Lee, J. (2018). Design, Modeling, and Analysis of a Railway Traction Motor With Independently Rotating Wheelsets. IEEE Transactions on Magnetics, 54 (11), 1–5. doi: https://doi.org/10.1109/tmag.2018.2842433

Wu, T., Jiang, D., Wang, Y., Lei, A. (2017). Study on a Harmonic Measurement and Analysis Method for Power Supply System. International Journal of Emerging Electric Power Systems, 18 (3). doi: https://doi.org/10.1515/ijeeps-2016-0271

Gou, B., Ge, X., Wang, S., Feng, X., Kuo, J. B., Habetler, T. G. (2016). An Open-Switch Fault Diagnosis Method for Single-Phase PWM Rectifier Using a Model-Based Approach in High-Speed Railway Electrical Traction Drive System. IEEE Transactions on Power Electronics, 31 (5), 3816–3826. doi: https://doi.org/10.1109/tpel.2015.2465299

Buriakovskyi, S., Maslii, A., Maslii, A. (2016). Determining parameters of electric drive of a sleeper-type turnout based on electromagnet and linear inductor electric motor. Eastern-European Journal of Enterprise Technologies, 4 (1 (82)), 32–41. doi: https://doi.org/10.15587/1729-4061.2016.75860

Ganji, B., Askari, M. H. (2016). Analysis and modeling of different topologies for linear switched reluctance motor using finite element method. Alexandria Engineering Journal, 55 (3), 2531–2538. doi: https://doi.org/10.1016/j.aej.2016.07.017




DOI: http://dx.doi.org/10.21303/2585-6847.2019.001025

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 Serhii Buriak

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

ISSN 2585-6847 (Online), ISSN 2585-6839 (Print)